High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70 Manuel d'utilisateur télécharger pdf

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685

YAMAHA OUTLAW SUPER DUTY EXTREME KIT INSTRUCTIONS

Model: 660 RHINO 04-07 / 660 GRIZZLY 02-07 (29.5” TIRES) Part #: HLCKY660GR-SX

Kits designed for Stock motor and stock exhaust at 0-3000 feet elevation.

THIS KIT IS NOT DESIGNED FOR USE WITH A MACHINED (OVERDRIVE) PRIMARY CLUTCH SHEAVE

ATV’s can be dangerous. EPI has no control over the use of any part. EPI expects the customer to exercise good

judgment as to the proper selection, installation, use and maintenance of any part. EPI assumes no responsibility for

damage or injury of any kind because of misuse, improper installation and improper application of any parts in any way

by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV

mechanic.

This product is NOT to be installed on any ATV that will be used by any person under the age of 16.

TOOLS NEEDED TO INSTALL CLUTCH KIT

- Set of metric sockets up to 27mm

- Phillips and flat tip screwdrivers

- 1 13/16 socket or wrench

- Torque wrench

- Spring tool or needle nose pliers

- Clutch compression tool (EPI Part # CCT510)

- 1/2 impact wrench

- 2-3 quarts of Yamaha Motor Oil

GASKETS NEEDED TO INSTALL CLUTCH KIT

- Order gaskets from your local dealer before you install clutch kit.

- Yamaha may call some gaskets carb gaskets. These are the correct gaskets:

- Internal Clutch Housing Gasket - part #5KM-15463-00-00

1. Grizzly - Remove the key from the ignition switch. Remove the seat, the small body piece between the seat and

the clutch cover, and the right side foot rest. Note the length of the bolts and their position. Remove the plastic

clutch cover being careful not to damage the gasket.

Rhino - Remove the key from the ignition switch. Remove driver’s and passenger seats. Remove black plastic

center console between the seats. The console lifts up and off from the engine bay. Remove plastic fasteners from

the seat frame cover on the driver’s seat frame. Remove cover. Remove the angle brace on top of driver’s seat

frame. This will give adequate room for removal of the secondary clutch. Remove front and rear vent lines.

Remove plastic clutch cover, note were the wire clamps are during bolt removal.

2. Once the clutch cover has been removed take the aluminum clutch guard off. You now should be able to see the

complete primary clutch. The clutch is filled with grease and must stay that way. Do not remove any grease unless

it is on the outside of the clutch, on the inner clutch sheaves where the belt rides, or on the belt. If any grease is on

these areas it will cause belt slippage. Clean these areas with contact or brake cleaner that doesn’t leave an oily

film.

3. Remove the large nut and washer that holds the primary clutch (normally 22mm) on. Once the nut has been

removed pull the clutch off of the machine. Remove the thin cover plate and the rubber o-ring. Carefully slide the

inside plate up and out of the clutch. Do not clean off any grease unless necessary. This should reveal eight clutch

rollers.

4. Remove one roller and press the inside weight out of it. You can usually use a 18mm/19mm or 11/16 socket and

push the weight out by hand. If needed, set the roller on a 26mm or a 1 1/16 socket, set the smaller socket on the

inner weight and lightly tap with a hammer to remove the inner weight. The weight can only be pushed in one

direction, make sure you are pushing it out the right way or damage can occur. Press in the new weight supplied in

the kit and place the roller back in the clutch. Repeat this step for the remaining rollers. NOTE: If your kit has

two different weights, be sure to place them directly across from each other (or every other one). This

keeps the clutch in balance. Make sure you have all eight of the rollers in the proper place and position. Install

the inside plate making sure all the rollers are in the proper location. Put the rubber o-ring and the thin cover plate

back on the clutch. Place clutch out of the way and start working on the secondary clutch.

EPIperformance.com

1 2

EPIperformance.com 1

Résumé du contenu

Page 1 - EPIperformance.com

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685 YAMAHA OUTLAW SUPER DUTY EXTREME KIT INSTRUCTIONS Model:

Page 2

5. Remove the large nut (22mm) that holds the secondary clutch on. Remove the clutch and the belt from the machine. Using a 1 13/16” socket or a la

Plus de documents pour Matériel High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70

Voir le document High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70 Manuel d'utilisateur

High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70 Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70. High Lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 700X Big Horn Crew (10-14) User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Matériel High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel High-lifter Outlaw Super Duty Extreme Clutch Kit for Yamaha 70