High-lifter Outlaw Clutch Kit for Polaris 500 Sportsman HO Car Manuel d'utilisateur télécharger pdf

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685

POLARIS OUTLAW SUPER DUTY KIT INSTRUCTIONS

Model:500 SPORTSMAN HO CARB 4x4 06/08-09 (27”-28” TIRES) Part #: HLCKP500SP

Kits designed for Stock motor and stock exhaust at 0-3000 feet elevation.

ATV’s can be dangerous. EPI has no control over the use of any part. EPI expects the customer to exercise good

judgment as to the proper selection, installation, use and maintenance of any part. EPI assumes no responsibility for

damage or injury of any kind because of misuse, improper installation and improper application of any parts in any way

by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV

mechanic.

This product is NOT to be installed on any ATV that will be used by any person under the age of 16.

TOOLS NEEDED TO INSTALL CLUTCH KIT

- 3/8, 7/16, 1/2 socket and wrench

- 5/8 socket

- Torque wrench

- Snap ring pliers

- Phillips screwdriver

- Side cutters

- 1/8 Allen wrench

- Primary Clutch Puller (EPI part # PCP-1)

ENGAGEMENT

- 21-2,300 Rpm’s

1. Remove the key from the ignition. Remove the left side foot rest by unbolting it from the fenders and frame.

Remove the zip ties or clamps on the vent hose coming from the top of the clutch cover. On some models you

might have to remove the seat and the left side body panel between the front and rear fenders to gain access to the

vent tube. Be careful not to damage the rubber boot when cutting the zip ties.

2. Using a screwdriver, loosen the clamp that holds the vent hose on the top of the clutch cover. Next remove the

clutch cover bolts. Note the length of the bolts and their location. Some models might have a little metal clamp at

the rear of the cover that needs to be removed, simply take a flat tipped screwdriver and pry the clamp off. Save

the clamp because you will need to reuse it. Remove cover slowly being careful not to damage the gasket.

3. Remove the belt. You can remove belt by squeezing the belt together between the two clutches, this will allow

enough slack in the belt to remove the belt. You can also twist the inside secondary (rear) clutch sheave towards

the rear of the machine and then pull on the belt to get enough slack in the belt to remove it. The primary (front)

clutch is pressed onto the crankshaft of the motor. Removal of the clutch is not required but does make the job

much easier. To remove the clutch a special clutch puller is needed, this tool is available through EPI (part # PCP-

1). Notice the “X” marked on the outside cover of the clutch, on the spider, and on the moveable sheave. These

are alignment marks from the factory and must line up when you reassemble the clutch. If you are not removing

the clutch see next step. To remove the clutch using a clutch puller remove the large center clutch bolt (5/8

socket). You need to use a small bar or large screwdriver and stick it through the clutch to stop the clutch from

rotating while you loosen the center bolt. Remove the center bolt, washers, and any spacers that are there. Thread

the clutch puller in by hand and tighten until the clutch pops off the shaft, you will need to hold the clutch from

rotating. Place clutch on a clean work surface and remove clutch puller.

4. If you are not pulling the primary clutch off the machine OR if you already have the clutch off the machine, remove

the six outside bolts from the cover. Next remove the center bolt allowing the cover and spring to be removed (this

bolt is already removed if clutch is off the machine).

5. With the spring removed you can change the weights. Using a 1/8”Allen wrench and a 3/8” wrench or socket

remove the bolt holding the weight in the clutch. Replace the stock weight with the weight included in the clutch kit

and install the bolt and nut. Repeat the same process for the other two weights.

EPIperformance.com

1 2

EPIperformance.com 1

Résumé du contenu

Page 1 - EPIperformance.com

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685 POLARIS OUTLAW SUPER DUTY KIT INSTRUCTIONS Model:500 SPO

Page 2

6. It is a good idea to clean your clutches. Using a clean rag and a contact/brake cleaner that DOES NOT leave an oily film or residue clean all are

Commentaires sur ces manuels

Pas de commentaire

High-lifter Outlaw Clutch Kit for Polaris 500 Sportsman HO Car Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel High-lifter Outlaw Clutch Kit for Polaris 500 Sportsman HO Car. High Lifter Outlaw Clutch Kit for Polaris 500 Sportsman HO Carb (06) & (08-12) Non-EBS User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel High-lifter Outlaw Clutch Kit for Polaris 500 Sportsman HO Car