High-lifter Outlaw Clutch Kit for Arctic Cat 700 H1 Mud Pro (0 Manuel d'utilisateur télécharger pdf

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪Fax (218) 829-1685

ARCTIC CAT OUTLAW SUPER DUTY KIT INSTRUCTIONS

Model: 700 H1 MUD PRO 4x4 2009-2010 (27”-28” TIRES) Part #: HLCKA700H1-1

Kits designed for Stock motor and stock exhaust at 0-3000 feet elevation.

ATV’s can be dangerous. EPI has no control over the use of any part. EPI expects the customer to exercise good

judgment as to the proper selection, installation, use and maintenance of any part. EPI assumes no responsibility for

damage or injury of any kind because of misuse, improper installation and improper application of any parts in any way

by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV

mechanic.

This product is NOT to be installed on any ATV that will be used by any person under the age of 16.

TOOLS NEEDED TO INSTALL CLUTCH KIT

- Set of metric sockets

- Phillips and flat tip screwdrivers

- #25, #30 Torx

- Snap ring pliers

- Torque wrench

- Spring tool or needle nose pliers

- Clutch compression tool (EPI part # CCT510)

- 1/2 impact wrench

- 2-3 quarts of Arctic Cat Motor Oil

GASKETS NEEDED TO INSTALL CLUTCH KIT

- Order gaskets from your local dealer before you install clutch kit.

- Internal Clutch Cover Gasket - part #0830-116

Engagement

23-2,400 RPMs

1. Remove the key from the ignition switch. Remove the foot rest including the brake petal and metal support bracket.

Remove clutch housing cover and gasket. Note the length of the bolts and their location.

2. Once the clutch cover has been removed you should be able to see the both clutches.

3. Remove the large nut and washer that holds the primary clutch (front clutch) on. Once the nut has been removed

pull the clutch off of the machine and place on a flat clean surface. Carefully slide the inside plate up and out of the

clutch. This should reveal eight clutch rollers.

4. Remove all eight of the stock rollers and set them to the side. Press in the new weights, supplied in the kit into the

new roller housings supplied in the kit and place the roller back in the clutch. The weights can only be pushed into

the housings one direction, make sure you are pushing it out the right way or damage can occur. Repeat this step

for the remaining rollers. NOTE: If your kit has two different weights, be sure to place them directly across

from each other (or every other one). This keeps the clutch in balance. Make sure you have all eight of the

rollers in the proper place and position. Install the inside plate making sure all the rollers are in the proper location.

Place clutch out of the way and start working on the secondary clutch.

5. Remove the large nut and washer that holds the secondary clutch on. Remove the clutch and the belt from the

machine. Using a compression tool (EPI part # CCT510) carefully compress the spring enough to take the pressure

off the snap ring. Remove the snap ring and slowly release the pressure off the spring. Remove the spring.

EPIperformance.com

1 2

EPIperformance.com 1

Résumé du contenu

Page 1 - EPIperformance.com

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪Fax (218) 829-1685 ARCTIC CAT OUTLAW SUPER DUTY KIT INSTRUCTIONS Model: 70

Page 2

6. Install the EPI secondary spring in the #1 hole in the helix and the B setting in the clutch. Align the helix on the splined shaft and place the

Commentaires sur ces manuels

Pas de commentaire

High-lifter Outlaw Clutch Kit for Arctic Cat 700 H1 Mud Pro (0 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel High-lifter Outlaw Clutch Kit for Arctic Cat 700 H1 Mud Pro (0. High Lifter Outlaw Clutch Kit for Arctic Cat 700 H1 Mud Pro (09-10) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel High-lifter Outlaw Clutch Kit for Arctic Cat 700 H1 Mud Pro (0