High-lifter Outlaw Clutch Kit for Arctic Cat 700 EFI (06-08) Manuel d'utilisateur télécharger pdf

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685

ARCTIC CAT OUTLAW SUPER DUTY KIT INSTRUCTIONS

Model: 700 EFI 4X4 2006-2008 (27”-28” TIRES) Part #: HLCKA700FI

Kits designed for Stock motor and stock exhaust at 0-3000 feet elevation.

ATV’s can be dangerous. EPI has no control over the use of any part. EPI expects the customer to exercise good

judgment as to the proper selection, installation, use and maintenance of any part. EPI assumes no responsibility for

damage or injury of any kind because of misuse, improper installation and improper application of any parts in any way

by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV

mechanic.

This product is NOT to be installed on any ATV that will be used by any person under the age of 16.

Tools needed to install clutch kit

- Metric socket set

- Torque wrench

- Spring tool or needle nose pliers

- clutch compression tool or shop press (EPI part # CCT510)

- 1/2” impact wrench

- Arctic Cat oil

- Punch or spanner wrench

- Phillips and flat tip screwdrivers

- Clutch shoe remover (Suzuki part # 09920-33540)

- Sliding shaft (Suzuki part # 09930-30104)

Gaskets needed

- Order gaskets from you local dealer before you install clutch kit

- Internal clutch housing gasket - part # 3403-070

Engagement

2,100 RPMs

1. Remove the key from ignition. Remove the right side foot rest including the metal support bracket. Remove cotter

pin and washer to remove brake pedal from master cylinder push rod. Remove the clutch cover. Note the length of

the bolts and their location.

2. Once the clutch cover is removed you should be able to see both clutches. Remove the plastic clutch guard.

Remove the bolt that holds the primary clutch (front clutch) on. Pull the clutch off the machine and place on a flat

clean surface. Slide the inside plate up and out of the clutch. This should reveal eight clutch rollers.

3. Remove one roller and press the inside weight out of it. You can usually use an 18mm/19mm or 11/16 socket and

push the weight out by hand. If needed, set the roller on a 26mm or a 1 1/16 socket, set the smaller socket on the

inner weight and lightly tap with a hammer to remove the weight. The weight can only be pushed in one direction,

make sure you are pushing it out the right way or damage can occur. Press in the new weight supplied in the kit

and place the roller back in the clutch. Repeat this step for the remaining rollers. NOTE: If your kit has two

different weights, be sure to place them directly across from each other (or every other one). This

keeps the clutch in balance. Make sure you have all eight of the rollers in the proper place and position. Install

the inside plate making sure all the rollers are in the proper location. Place clutch out of the way and start working

on the secondary clutch.

EPIperformance.com

1 2

EPIperformance.com 1

Résumé du contenu

Page 1 - EPIperformance.com

8273 Industrial Park Road ▪ Baxter, MN 56425 ▪ (218) 829-6036 ▪ Fax (218) 829-1685 ARCTIC CAT OUTLAW SUPER DUTY KIT INSTRUCTIONS Model:

Page 2

4. Remove the bolt that holds the secondary clutch on. Remove the clutch and belt from the machine. Using a spanner wrench or punch and a hammer lo

Commentaires sur ces manuels

Pas de commentaire

High-lifter Outlaw Clutch Kit for Arctic Cat 700 EFI (06-08) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel High-lifter Outlaw Clutch Kit for Arctic Cat 700 EFI (06-08). High Lifter Outlaw Clutch Kit for Arctic Cat 700 EFI (06-08) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel High-lifter Outlaw Clutch Kit for Arctic Cat 700 EFI (06-08)